mahos.inst.lockin.SR860

class mahos.inst.lockin.SR860(name, conf, prefix=None)

SRS SR860 Lockin Amplifier.

__init__(name, conf, prefix=None)

Methods

__init__(name, conf[, prefix])
configure(params[, label])	Configure the instrument settings.
get(key[, args, label])	Get an instrument setting or measurement data.
get_Rexpand()	get output expand factor for R.
get_Roffset()	get offset value for R in percent.
get_Roffset_enable()	get if offset for R is enabled.
get_Rratio_enable()	get if ratio mode for R is enabled.
get_Xexpand()	get output expand factor for X.
get_Xoffset()	get offset value for X in percent.
get_Xoffset_enable()	get if offset for X is enabled.
get_Xratio_enable()	get if ratio mode for X is enabled.
get_Yexpand()	get output expand factor for Y.
get_Yoffset()	get offset value for Y in percent.
get_Yoffset_enable()	get if offset for Y is enabled.
get_Yratio_enable()	get if ratio mode for Y is enabled.
get_adv_filter()	get advanced filter.
get_amplitude()	get amplitude of internal oscillator.
get_ch1_mode()	get ch1 output mode (True: R, False: X).
get_ch2_mode()	get ch2 output mode (True: Theta, False: Y).
get_coupling()	get input coupling (True: DC, False: AC).
get_current_gain()	get current gain (True: 100 M Ohm, False: 1 M Ohm).
get_freq()	get frequency of internal oscillator.
get_ground()	get input ground (True: Grounded, False: Floating).
get_harmonics()	get current harmonics degree.
get_input_mode()	get current signal input source (True: current, False: voltage).
get_input_range()	get input range.
get_input_source()	get current signal input source (True: A-B, False: A).
get_param_dict([label])	Get ParamDict for label.
get_param_dict_labels()	Get list of available ParamDict labels.
get_phase_offset()	get current phase offset in degrees.
get_ref_edge()	get current reference source rdge.
get_ref_imp()	get current reference source input impedance (True: 1M Ohm, False: 50 Ohm).
get_ref_source()	get current reference source.
get_sensitivity()	get sensitivity.
get_sensitivity_float()
get_slope()	get slope in dB/oct.
get_sync_filter()	get sync filter.
get_time_constant()	get time constant.
lock_params(param_names)
release_params(param_names)
set(key[, value, label])	Set an instrument setting or commanding value.
set_Rexpand(fac)	set output expand factor for R.
set_Roffset(offset_percent)	set offset value for R.
set_Roffset_enable(enable)	set if offset for R is enabled.
set_Rratio_enable(enable)	set if ratio mode for R is enabled.
set_Xexpand(fac)	set output expand factor for X.
set_Xoffset(offset_percent)	set offset value for X.
set_Xoffset_enable(enable)	set if offset for X is enabled.
set_Xratio_enable(enable)	set if ratio mode for X is enabled.
set_Yexpand(fac)	set output expand factor for Y.
set_Yoffset(offset_percent)	set offset value for Y.
set_Yoffset_enable(enable)	set if offset for Y is enabled.
set_Yratio_enable(enable)	set if ratio mode for Y is enabled.
set_adv_filter(enable)	set adv filter.
set_amplitude(ampl)	set amplitude of internal oscillator.
set_auto_phase_offset()	set auto phase offset.
set_auto_range()	execute auto range setting.
set_auto_scale()	execute auto scale setting.
set_ch1_mode(output_R)	set ch1 output mode (True: R, False: X).
set_ch2_mode(output_Theta)	set ch2 output mode (True: Theta, False: Y).
set_coupling(DC_coupling)	set input coupling (True: DC, False: AC).
set_current_gain(gain_100M)	set current gain (True: 100 M Ohm, False: 1 M Ohm).
set_freq(freq)	set frequency of internal oscillator.
set_ground(ground)	set input ground (True: Grounded, False: Floating).
set_harmonics(harmonics_deg)	set harmonics degree.
set_input_mode(current)	set signal input source (True: current, False: voltage).
set_input_range(input_range)	set input range.
set_input_source(diff_input)	set signal input source (True: A-B, False: A).
set_phase_offset(phase_deg)	set phase offset in degrees.
set_ref_edge(edge)	set reference source edge.
set_ref_imp(imp_1M)	set reference source imput impedance (True: 1M Ohm, False: 50 Ohm).
set_ref_source(src)	set reference source.
set_sensitivity(sens)	set sensitivity.
set_slope(slope_dB_oct)	set slope in dB/oct.
set_sync_filter(enable)	set sync filter.
set_time_constant(cons)	set time constant.

Attributes

PARAM_NAMES
Sensitivity_to_Float